Fast 2804 v 7 rev 1 firmware. Firmware update and automatic configuration

The Sagemcom Fast 2804 v7 router is designed to connect to the Internet using ADSL (thin telephone cable) or Ethernet (eight- or four-wire twisted pair).

You can also use it to create a home wireless network and connect an IPTV set-top box from Rostelecom.

This article describes the process of setting up the Sagemcom Fast 2804 router for correct operation in the Rostelecom provider network.

Connection

Before starting setup, users will need to properly connect the purchased router. Using the patch cord included in the kit, connect the network card port of your computer or laptop to one of the yellow LAN ports 2-4.

If the Internet comes to you via telephone line– connect the cable to the connector labeled “ADSL”. If you are provided with a more modern Ethernet connection, plug the supplied cable into the LAN1 port.

Now you can connect the Sagemcom Fast 2804 to power, turn it on and start setting up.

Firmware update and automatic configuration

If you purchased a router from a Rostelecom store, it will come with a special DVD designed to automatically configure the device.

Also, using the disk, users need to update the Sagemcom Fast 2804 firmware version from v5 to v7. The v7 system was developed by Rostelecom specialists and adapted for the most stable connection with the provider’s servers.

Insert the disc into your computer's DVD drive. After this, the Rostelecom Setup Wizard will be automatically launched. You can set all the necessary parameters using the Wizard - in this case, select “Full setup”. Then just follow the program’s instructions; you don’t need to connect to the router’s web interface.

If you prefer to do everything yourself, select “Update”. Wait a moment until firmware v7 is installed on the Sagemcom Fast 2804, then close the program and proceed to the next step in the guide.

Authorization in the Web interface

• Launch any internet browser.
  In the addressing line, you must enter the device address, which is indicated on the sticker on the bottom cover of the router. If there is no sticker on the case, you need to go to the properties of the local connection and look at the value of the “Default gateway” parameter.
• A pop-up window will open in which users need to provide a login and password to access the router management menu. This information is also indicated on the sticker. You can try the most commonly used combination: "admin" and "admin".

• If you did everything correctly, the interface for controlling the operation of Sagemcom Fast 2804 v7 will open.

Setting up a network connection

• Using the navigation menu on the left side of the window, go to the “Advanced” tab.
• Open the “WAN service” section and delete all existing connections. To do this, mark them and click “Delete”.
• In a similar way, delete all the contents of the “Second Level Interface” section.
• Click on the “Add” button.
• Rostelecom subscribers must indicate the values ​​of the VCI and VPI parameters, which depend on the region of residence. You can clarify the correct parameters by contacting technical support by phone (a list of numbers is available).

• Click Apply and Save.
• Go to the “WAN Service” tab and click “Add”.
• Select the connection you just created from the drop-down list and proceed further.
• In this step, users need to specify the connection type. In most cases, you will receive Internet from Rostelecom via a PPPoE connection.

• Enter your username and PPP connection key, which are specified in the service agreement with Rostelecom (all information is available). You can specify any service name, it does not affect anything.

• Check the box next to “Retry PPP on error”.
• You can skip the remaining steps. Click "Apply and Save" to complete the settings.

Setting up a router to work with a TV set-top box

If you want to connect a set-top box via the Sagemcom Fast 2804 v7 router, you must do the following:

• In the “Second Layer Interface” tab, create another connection (the VCI and VPI values ​​for IPTV will be different).
• In the “WAN service” section, create a new object and select the created connection.
• Select the service type "Bridge" and click "Apply".

• Open the “LAN” tab.
• Check the box next to “Disable DHCP server”.
• Enable the IGMP Snooping and IGMP Proxy on Bridge options.

WiFi Configurations

• Expand the “WLAN” category and go to the “Basic” section.
• Activate the “Enable wireless network” and “Enable multicast transmission” items.
• Enter the access point name in the SSID field.
• Go to the "Security" category.
• Select authentication using "WPA-PSK", encryption using "TKIP and AES".

• Enter your access key (at least 8 characters).
• Click "Save".

This completes the router setup. In the “Management” section, find the “Reboot” tab and restart your modem to activate all the changes made.

We turn on the modem, connect it to the PC, connecting with a cable any Ethernet port of the modem to the connector of the PC’s network card.

By default, the modem has a DHCP server enabled, so in the network card settings you can select the option - “Obtain an IP address automatically"or enter addresses manually by setting the following values:

IP address - 192.168.1.2 to 253

Mask - 255.255.255.0

Gateway - 192.168.1.1

DNS 1st - 195.46.116.1

DNS 2nd - 195.46.96.1

Launch the web browser, enter the address in the address bar - 192.168.1.1 and on the keyboard press the " Enter."

A login and password entry window appears on the screen, in which you need to enter the following values: User - admin and password - admin. You can check the box "Save password", then you won’t have to enter them when you reconnect to the modem.

Attention!!!

If the login and password entry window does not appear during connection, try switching the Ethernet cable from the first port of the modem to the second and try again. If there is no connection to the modem on all four Ethernet ports, you must use the command ping 192.168.1.1 check the availability of the modem by also connecting to each port one by one. If there are no responses, as shown in the figure below, the modem must be replaced. Most likely it is faulty!!!

If a window appears when connecting, then enter in the fields “ User" and "Password" - the word "admin" " and press the button " OK ", as shown in the picture:

If the data is entered correctly, the following window will open:

In the upper right corner, highlighted in blue, information about the line status and modem connection speed is displayed. Internet network availability indicator - relevant when the modem is configured to Router.

The table in the center of the screen (highlighted in red) shows the software version installed on the modem - this information is very important!!!

Features for firmware version - 6.35 and 6.41

In the factory settings of the modem, one PVC with values ​​of 1/69 is registered on it

The 1st Ethernet port of the modem is reserved for an external WAN connection, and therefore it is not possible to connect to the modem through it (the ping command also does not work).

Below we will consider the sequence of steps to configure the modem for:

Internet access,

Interactive TV set-top box connections,

Enabling Wi-Fi and transmitting multicast traffic via Wi-Fi.

We will show you how to enable/disable the DHCP server and the ability to forward ports to organize access from the Internet to internal resources located in local network user.

Before you start setting up the modem, especially if it was previously configured for other services, or installed by another user, we strongly recommend that you perform a reset to factory settings. This can be done by pressing the button on the back panel of the modem - “ Reset "and hold it with the modem power on for more than 20 seconds. The second option is to perform this operation by selecting the items “ Management » - « Settings options" - " Reset " and in the central part of the window click on the button "Restore default settings" and confirm your choice by clicking on the " OK ":

As a result, a window will appear with the following message (highlighted in red):

After 2 minutes you can start setting up the modem.

The first thing you need to do for a modem withFirmware version 6.35 and 6.41- this is to enable the ability to use the 1st Ethernet port to connect a computer. To do this, go to the menu item “Additional settings", then submenu "Level 2 interface" and the menu item " ETH interface " and in the table that opens, delete the interface " eth0/eth0 ", which is written there by default:

To do this, check the box and click on the “ Delete "As a result, the table will become empty and through the first Ethernet port you can connect and configure the modem and work on the Internet!!!

For a modem with firmware version 5.47 - go to the ETH interface menu, no need to go!!! Since by default it does not have a port assigned for an external WAN connection.

Then select the menu item "Additional settings", submenu "WAN service ", mark all the entries in the table by checking the box " Delete "(highlighted in red in the figure below), and delete them by clicking on the corresponding button:

The result should be an empty table, as shown in the figure below:

Then go to the submenu “Level 2 interface" and select the submenu " ATM PVC interface ", here we also delete all records in the table by checking the box " Delete " and clicking on the corresponding button:

As a result, we get an empty table:

Now here we begin to add records with the values ​​we need PVC . Let us remind you that to access the Internet the following values ​​are used: 0/35 and 0/100 , and for the interactive TV service to work, the following values ​​are required: 1/35, 1/36 and 1/37 mandatory prescribed in the regime bridge.

Press the button " Add " and in the window that opens we see the following elements:

Fields highlighted in red - need to be changed according to those values VPI/VCI , which need to be added, the default value is 0 and 35 - such values ​​are needed, so we do not change them.

Pay attention to the element highlighted in blue - it says that if you add PVC will be set to mode PPPoE or Bridge , then the value should be - EoA. This is the default - don't change it!!!

Below in the same window, leave the remaining elements unchanged and click on the button - “Apply/Save" - as shown in the figure below.

We add in the same way PVC with VPI/VCI values ​​of 0 and 100:

and then three more entries with values VPI/VCI - 1/35, 1/36 and 1/37 respectively. The figure below shows only the addition PVC with 1/35 values - to add entries PVC with values ​​1/36, 1/37 - similar actions.

The result is a table with five records - as shown in the image below:

Go to the menu " WAN service "and configure the operating mode of the ones we added PVC , pressing the button - " Add " as shown in the picture below:

In the window that opens, at the bottom, there is a drop-down list containing the names PVC , they are usually listed in this list in the order they were added.

Let's start in order and set up PVC to access the Internet. Press the button " Next » and in the form that opens, set the operating mode of the modem.

If it works in mode - Bridge , then we mark the position - Bridging

For Bridge mode everything is quite simple, click on the button “ Next ", a window appears, as shown in the figure below, in which, after clicking on the button "Apply/Save» - selected mode for this PVC - saved and recorded in the table:

To add other PVCs, press the button “ Add "and configure them:

Let's take a closer look at the setup process PVC with values ​​0/100 in PPPoE mode (Router).

:

Selecting the PPP over Ethernet option , click on the button “ Next."

For firmware version 6.41:

Select the option "PPP over Ethernet" "check what's in the dropdown list" Network Protocol Selection "The value is set to " IPV4 Only " and click on the button " Next."

In the next window, enter the login and password from the contract. The service name can be specified - inet . We put a tick in the position - “Repeat PPP on authentication error»:

We don’t change anything else on the form and at the very bottom click the button - “ Next."

For firmware version 5.47 and 6.35:

In the next window, leave everything unchanged and click the “ Next »:

In the window " DNS server configuration"We also do not change anything and press the button " Next »:

For firmware version 6.41:

In the window that opens, in the list "Available routed WAN interfaces"(highlighted in green) select the value " ppp1.1 " and transfer it using the button (highlighted in blue) to the field "Selected Default Gateway Interfaces" (highlighted in red) and press the button " Next »:

In the next window "DNS server configuration" carry out the transfer of value " ppp1.1 " from the field on the right side "Available WAN interfaces" using the button (highlighted in blue) in the " fieldSelected DNS server interfaces" and press the button " Next »:

As a result, we see the final form:

To save the settings, click the "Apply/Save».

We configure the mode " Bridge » those PVCs that prescribed Interactive TV services for operation - they matter - 1/35, 1/36 and 1/37 . The setup is carried out similarly to the actions that were shown in this instruction above in the text, when registering PVC with the values 0/35 .

As a result, we have five in the table PVC, as shown in the picture below:

For firmware version 5.47 and 6.35

For firmware version 6.41

If you will connect a TV set-top box, then you need to group the ports; to do this, in the menu on the left, select the item - “Interface grouping».

In it we will create a group uniting PVC with values ​​1/35, 1/36, 1/37 with the fourth Ethernet port of the modem:

Click on the button " Add "and in the form that opens, fill in the fields, as shown in the figure below, set the group name - IPTV and grouping PVC (1/35, 1/36, 1/37)

For firmware version 5.47 and 6.35

For firmware version 6.41

and select the 3rd Ethernet port - eth3 , since the count starts from zero, in fact this will be the 4th port of the modem:

To save the settings, click the button at the bottom “Apply/Save"As a result, we see in the table a created group with the name - iptv:

For firmware version 5.47 and 6.35

For firmware version 6.41

Note that when enabled DHCP -server - into the port dedicated for connecting a TV set-top box - addresses are not distributed, so you don’t have to turn it off. This is a definite advantage when connecting via Wi-Fi.

Turning on Wi-Fi

Select the item " WLAN setup »

Default Wi-Fi enabled, this is indicated by the marked field - “Enable wireless network" If you uncheck this checkbox, Wi-Fi will not work.

Mark in the field - “Enable multicast transmission via wireless network» - allows you to use an IPTV player to watch channels on a PC connected via WiFi . There is no need to make changes to grouped interfaces!!! It should be remembered that if the set-top box is turned on and the IPTV player is running at the same time, only one of them will work, since the speed will not be enough.

If the checkbox is not checked, as shown above, then multicast traffic will not flow over Wi-Fi!!!

SSID field - this is the name of the wireless network that will be displayed when searching for all available networks, so we recommend that you write here after the word ROSTELECOM, the house number and apartment number - for example: Rostelecom_312_33

Go to the menu item - “ Safety " and set the values ​​of the drop-down fields as shown in the figure below.

In the WPA/WAPI password field - enter the password that will be used as a key when connecting to this access point. As a rule, a password is prescribed to connect to the Internet.Apply/Save».

Disabling the DHCP server.

If you need to disable the DHCP server, you need to select “Additional settings", then submenu " LAN " and put a dot in the position - "Disable DHCP server»:

To save the settings you need to press the button - “Apply/Save»

Remote desktop access on the user's PC

To organize access from the Internet, for example, using the “Remote Desktop” application on the user’s PC, you need to select the menu item “Additional information", submenu "NAT" - subsection " Virtual servers"and carry out the settings as shown in the figure below:

Use interface- you need to select from the drop-down list exactly the one through which it rises PPPoE connection.

Service name - you can select from the drop-down list of preset values ​​or set it manually, as is done in the example - a name has been entered RDP.

IP address - the field must contain the value of the IP address on the network card of the PC in the user’s network to which he wishes to access - in our example - 192.168.1.3

The range of external ports and the range of internal ports must be indicated; if there is only one port, then the same values ​​are indicated - in our case, the port for remote access - 3389 it is on this port that the application runs "Remote Desktop».

To save the settings you need to press the button - “

Instructions for setting up the router: (Doc file)

To update the firmware, you need to go to the router menu:

Instructions for setting up the SagemCom 2804 router for Fttb (“->” arrow means “click”).
First, open your browser and enter 192.168.1.1 -> “login” in the address bar.

1. RESET THE ROUTER SETTINGS.
1.1 -> “MANAGE” -> “SETTINGS” -> “RESET” -> “RESTORE DEFAULT SETTINGS”.
2.REMOVE STANDARD SETTINGS.
2.1 -> “ADDITIONAL SETTINGS” -> “WAN SERVICE” -> SELECT EVERYTHING IN THE TABLE WITH A CHECK -> “DELETE”.
2.2 -> “2ND LEVEL INTERFACE” -> SELECT EVERYTHING IN THE TABLE WITH A CHECK -> “DELETE”.
2.3 -> “ETH INTERFACE”, IF CREATED, DO NOT DELETE.
3. CREATE WAN SERVICE SETTINGS.
3.1 -> “WAN SERVICE” -> “ADD” -> “NEXT” -> “NEXT”.
3.2 CHECK THE CHECKS ON -> “REPEAT PPP IN AUTHENTICATION ERROR”, AND IF THERE IS THE SAME BELOW -> “ENABLE NAT”, AND -> “ENABLE FIREWALL”.
3.3 ENTER YOUR LOGIN AND PASSWORD -> “NEXT”, “PPP”-MOVE LEFT, “USB”-MOVE RIGHT, -> “NEXT”, “USB”-MOVE RIGHT, “PPP”-MOVE LEFT, -> “NEXT” , -> “APPLY AND SAVE”.
4. IN “WAN SERVICE” WE CREATE SETTINGS FOR “TV”.
4.1 -> “ADD” -> “NEXT”, SELECT THE BOTTOM ONE IN THE LINE -> “BRIGING” -> “APPLY AND SAVE”.
5. WE CREATE A GROUP FOR “TV”.
5.1 -> “GROUPING INTERFACES”, -> “ADD”, GROUP NAME “TV”, “BR_ETH/ETH0.2” MOVE TO THE LEFT, “ETH3/ETH3,ETH2” MOVE TO THE LEFT -> “APPLY AND SAVE”.
READY!!!

ATTENTION!!! After setting up the modem, it is recommended to change the standard login/password to the web interface.

Using the Sagemcom Fast 2804 v7 router, you can connect to the Internet via Ethernet (eight- or four-wire twisted pair) or ADSL (thin telephone cable) technologies. In addition, this device allows you to create a wireless network and connect an IPTV set-top box from Rostelecom. In this article you will find a description of the process of setting up the Sagemcom Fast 2804 router to work on the Rostelecom network.

Connecting the router to the computer

Before you begin setting up the router configuration, you need to connect it. To do this, connect your computer to one of the LAN ports (LAN2-LAN4) of the router using the patch cord that comes with the device.

If your Internet is via a telephone cable, connect it to your router using the ADSL port. If you have Internet access via Ethernet technology, connect the cable to the LAN1 connector. Then, plug the router into a power outlet.

How to update the firmware and run automatic router setup

A router purchased at a Rostelecom showroom comes with a special DVD that is required to automatically configure the device. Using the same disk, the subscriber is asked to update the Sagemcom Fast 2804 firmware version from v5 to v7. This is necessary for a more stable connection with servers, because... This version was developed and adapted specifically for Rostelecom.

After you insert the disc into your computer's drive, the Rostelecom Setup Wizard will launch automatically. Using the Setup Wizard, you can set all the necessary parameters without connecting to the router’s web interface. To do this, select "Full setup" and follow the program instructions.

If you want to do without the Wizard and make all the changes yourself, select "Update". Wait until firmware v7 is installed on the router, after which you can close the program.

Login to the router admin panel

After updating the firmware, you can begin directly configuring the device in the Web interface:

• Open an Internet browser (browser) on your computer.
• In the address bar, enter the address of your router, which you can find on the label on the bottom cover of the device. If this data is missing, go to the properties of the local connection and find the "Default gateway" parameter. This is the address of your router.
• In the window that opens, the system will ask you to enter your login and password to access the router configurations. This data is also indicated on the router label. The most common combination is "admin" and "admin".

• If the data is entered correctly, the main page of the Sagemcom Fast 2804 v7 web interface will open.

Setting up a network connection

• Select the "Advanced" tab from the menu on the left.
• Enter the "WAN service" section. Check all existing connections and click the Remove button.
• In the Second Layer Interface section, also delete all content.
• Click the "Add" button.
• Now you need to specify the values ​​of the VCI and VPI parameters. These data are individual for each region of Russia. You can find out the values ​​of these parameters by contacting .

• Click "Apply and Save".
• Go to the "WAN service" section and click "Add".
• Select the connection you just created from the list and proceed further.
• Now you need to specify the connection type. As a rule, Rostelecom provides Internet via a PPPoE connection.

• Specify the username and key for the PPP connection. This information is usually provided in about the provision of services. If a copy of the agreement is lost, you can contact Rostelecom customer support. You can specify any name for the service.

• Check the "Retry PPP on error" checkbox.
• You don't need to change anything in the following steps. When finished, click "Apply and Save".

Setting up a router to work with Rostelecom television

To connect a TV set-top box via the Sagemcom Fast 2804 v7 router, you must do the following:

• In the “Second-level interface” section, you need to create another connection and enter the VCI and VPI values, which will differ from the values ​​entered when setting up the Internet.
• In the "WAN service" section, create a new object and select the created connection.
• Select the service type "Bridge" and click "Apply".

• Open the "LAN" tab.
• Here you need to check the “Disable DHCP server” checkbox.
• Check the "IGMP Snooping" and "IGMP Proxy on Bridge" options.

Wi-Fi setup

• In the "WLAN" category, select the "Basic" section.
• Activate the "Enable wireless network" and "Enable multicast transmission" options.
• In the "SSID" line, write the name of your access point.
• Then go to the "Security" category.
• Select authentication using "WPA-PSK", encryption using "TKIP and AES".

• Set your password (at least 8 characters).
• Click "Save".

When finished setting up your router, reboot it. To do this, use the "Reboot" button in the "Management" section or simply disconnect the router from the power supply for a few seconds.